Mostly all the doors that are manufactured on specialized factories are designed for a certain thickness of the walls. It in many cases is about 70 or 80 mm. But how to be owners of country or ordinary private houses? They have often much thicker of apartment options.

In this case, it can be separated by opening sheets of drywall or it is even easier to apply - to apply the installation of the dog to interior doors. The way simple, and requires significantly less time and effort to implement it. Some home home houses are plastered in those places where the box is absent. But, nevertheless, less labor-intensive and more efficient is the method of installing good. Therefore, you need to carefully figure out how to fix good it.

Dobors are two racks located in a vertical position, and one horizontal bar. It is located at the top of the day. Thus, the finished design increases the box itself. Among the frequently used material for the manufacture of the design, the most popular are the Fiberboard, array and MDF. They are wear-resistant and available in their price category.

Measurement and preparatory work

Installing a problem is needed primarily in order to reliably fasten the platbands. Perform the correct fixation of the platbands, if the products are placed by the end to the wall plane. It is best to remove measurements with the assembled and installed box. After that, the installation of good ups is already carried out.

Initially, set ruler On the box of the box and keep it strictly perpendicular to the wall. You need to determine the size of the upper and lower part of the product. In this case, the width of one kind in different parts may differ, since the walls are almost always imperfect. All data should be made on paper not to confuse the product parameters.

Many experienced specialists enjoy a more accurate method. Measurement of all kinds is made through Corolnic and Smooth Rake. The first device is installed in the landing place, and the second is applied to the wall plane. Where the carbon intersects with a rack and there will be a width pointer. The size of each slope must be carefully checked, since the error can be allowed at any stage.

After the manipulations conducted, it is proceeded to cut the board. It is easy to do with a hand saw. The electrolovik and stationary machine are also well suited, provided that they are presence.

Installation

Installing DOPs on the interior door with their own hands simple enough. To do this, you need to decide first of all, with the type of box. They are:

• with groove;
• without a groove.

The first option is the easiest. It has everything to carry out the installation of good. The versatility of the presence of the groove is that it allows you to adjust the position of the good. And also this adaptation is significantly saved. Adjusting the bar, it can be immediately mounted on the wall.

Installation on a self-tapping screw

The first thing you need to do is drill Satay under the self-sufficiency. As a rule, the MDF boards, of which most often make blanks, approximately 10 mm in thickness. This means that the drill must be a diameter of a maximum of 9 mm. To more accurately and reliably fasten to the interior door DOP, the diameters of the drill and hats of the self-tapping screws must coincide.

Directly the self-tapping screws choose such a length so that they literally climbed into the canvas of the box. If products are too long - wood cracks. Mandatory condition - the use of wood dried. They are characterized by the presence of special brands in the form of needles. Such products are able to accurately center the holes.

When the tool is selected, drills the hole for the self-tapping screw. At the same time, it is necessary to choose not perpendicular direction, but to set the drill at an angle. This method will allow to consolidate the additional element to the central part of the door box.

The first screws are screwed up vertical racks. After their fixation, the horizontal plank is started.

Installation on carnations

Another very effective way to install the door duty is the method of applying carnations.

For installation, it will be necessary to drill small holes in which finish nails will be clogged.

Critically important - drilled holes must be less than the length of the nails!

After that, it is necessary to insert cloves with sharp side to the outside, and the caps are removed with nipples. A mounting bar is often used to clog nails.

When all the fastening elements are in place, you can put good things and carefully peel the product connecting it with the box.

Installation on the foam

Installing the door of the door for this principle is performed several times faster than the rest of the methods. Products are installed in place. After that, they need to be subcined from the inside. Surfaces should cuddle to the door box. Customize the opening can only after careful cleaning and compulsory wetting surface.

Installation of telescopic good

This type of product has its own unique advantages.

• It can be tightly fixed in the overall design.
• The surfaces are reliably adjacent to each other.
• It is quite simple to connect the components of the parts.
• DOORS If this configuration can be shifted either up, or down.
• It is possible to move them inside and outward products.
• The stock of parts is small, but these millimeters allow you to maximally adjust the position of the problems and correct the errors that were allowed during markup.
• Special "adjusting" grooves make the design comfortable and easy to install.

Together with the box

The way is to collect the entire design before its fastening against the wall. And the box, and goodholds are going to one whole. Additional elements that are expanding the discounts are attached to the door frame. After that, the finished product is fixed.

The following tips will be useful:

• Carnations are used solely in order to press the extra panels to the door frame. They do not hold from offset.
• In the process of drilling holes, you can make a crack on the front side of the product and between the slopes. Therefore, all work must be done carefully.

On the OBI Hypermarket Catalog page, components for interroom doors are collected. Here you can purchase separate planks and other accessories worth from 50 to 4500 rubles. There are about 300 items of goods in this category.

When buying components from this section, you must find accurate:

• . Coloring and texture of the product.
• . Dimensions in height, width and thickness.
• . Type of finishing facial surface.

Door boxes are designed to be installed around the perimeter in the opening of standard sizes. They are a product prepared for installation, sold complete with accessories and fasteners.

Prints are used for the decorative framing of the opening. They hide the space (gaps) between the cloth and the wall. Dobra are installed to expand the door design and the original scenery of the seasplets. These decorative elements manufacturers are made in the same color gamns as the canvas of all the main series.

Order in the shop of trial components for installing interroom doors with and manufacturer's guarantees.

Payment and delivery methods

1. Purchase the item online with delivery

• . Pay for the order you can cash or non-cash payments.
• . You agree with the date and time of delivery when the order is confirmed.
• . Conditions for free provision of services depend on the city, the amount and weight of the product.
• . Unloading of goods, lifting and transfer relate to additional services and can be paid separately, specify from the store operator.

Detailed information about intervals and zones by city, unloading and lifting conditions are located, where you can independently calculate the cost of your delivery, specifying the postal address and parameters for unloading.

1. Order and take yourself where you are comfortable

• . When filling out the order form, specify the date and time to you and the time to visit the hypermarket.
• . You can pay for the purchase by cash or non-cash payment at the store's cash desks.

Acquired goods can be independently pick up in any of the Obi shops in Moscow, St. Petersburg, Ryazan, Volgograd, Nizhny Novgorod, Saratov, Kazan, Yekaterinburg, Omsk, Krasnodar, Surgut, Bryansk, Tula and Volzhsky.

06.04.2014 07:00

Buying interroom doors we are faced with phrases: "If you need to install good, then ..." , do you need good? "... etc. So what is good or good? Throwing to explain in detail:

What are the good?

Dobor is a "board" a length of a little more than 2 meters (207-215cm), a thickness of usually 10 mm, which on one side is finished in the same color as our door. But the size of the width depending on the door model, there are different standards, the most common dimensions of the width of the problem: 10 cm, 12 cm and 15 cm, less often - 20cm, there are even 40 cm wide. If you need even wider than good, then this is already to order. I do not see the point of it even wider than 20 cm, since you can always make a composite good (combine them), which is much easier than to establish a 440 cm width.

So why do you need good?

In order to prevent the width of the door frame, the width of which is less than the thickness of the doorway wall. For example, the thickness of the wall in the opening, where we want to install the door, is equal to 17 cm, and the width of the door frame is 7 cm, hence it follows that we need to retalor 17-7 \u003d 10 cm. We take into account even that the good board is usually inserted on 1 cm inside (in the groove on the back of the box). So we will need a good one width 11 cm. We look at the existing standards and, if there are 12 cm, then we take 2.5 sticks (good boards) on this opening. Excess centimeter The door installer will make it. If there is no 12, and there are 15 cm, then it means we take them.

Another example : The thickness of the wall of the doorway is at the bottom of 8 cm, and at the top 7-7.5 cm. What to do? It turns out that we need a good (we consider the maximum width) 8 -7 +1 \u003d 2 cm? Are there such good? Such a width of goodness you are unlikely to meet, the answer is simple - on 1 opening we will need a 1.5-fold boards with a width of 10 cm (that is, 1 kind of installer will dissolve for two himself, and the cutting side of the good in the grooves in the grooves). The above examples of the calculation of volunteers are for top of standard typewhose platbands are not telescopic. If you have telescopic platbands (watch from the end G.- shaped), that is, the platbands are inserted with their protruding spike in the grooves of the box and thereby allow you to extend somewhere more, and somewhere less in the range 0-1.5 cm. So using telescopic concubine , we will manage without goodness for openings with a thick wall to 9 cm For the bulk of the types of doors, as well as for doors Profile Dors , despite the fact that the spike at the platbands for these doors 2 cm. That is, if you have the thickness of the wall varies from 8.5 to 10 cm, I will need a good! An experienced master will cut the shelf of the groove on the door frame in a circle and secure the sawn-siled on the self-tapping screw or studs. This is a difficult moment in the work, and no doors manufacturer of such a method of fastening of good will show you. Use!))

Generally O. telescopic plates I want to say a lot more. Indeed, the monument to the inventor needs to be put. After all, the advantage of telescopes is not only that we save on doggers, judging by the examples above, we also won the doors in the aesthetic design, with uneven walls of the opening! In order for the door to closely closely (correctly), the left and right wall of the doorway must be in the same plane, and not a propeller! In reality, it rarely happens, especially if the repair of the walls was not in beacons. So just here we are very helpful to telescopic platbands! That is, we can drown a little door frame (up to 1 cm) Inside the opening, and where it is necessary - to push the flush with the wall, thereby still adjust the door on the plumb. So besides the pros, in the use of telescopic platbands, I do not find minuses.

In our store interroom doors with telescopic platbands You can choose in the following categories:

How much does it cost to install good?

The installation of good things goes as an additional service - a thin and weighty "nuance", about which as a rule, the client learns during the installation process, which is later disappointed, since the final amount of the door mounting is already different from the original! That is why it is not necessary to be kept on the low door installation price. The cost of installing the goodness to the interroom door will usually depend on the width of the good. Some firms increase the value of the installation of sobers for every 5 cm Widths!

What are we better?

• Ordering the doors and their installation with us, we take into account all your wishes and, after measurement, calculate the amount of goodness so that after the installation is not too much, and therefore you do not have to overpay
• Installation of doors with a good or without good, we have the same.
• The price for assembly is negotiated at the measurement and later does not change, even if we did not take into account something.
• Our reputation is important to us, so warranty On the installation of interroom doors we give 3 years!

But how do goodness look at the example of our work:

The table will help you choose the right amount of kinds under the thickness of the walls of doorways. .

If you have any questions -

Sections Articles:

The manifold of modern manufacturers and the presence of their own technical conditions led to the fact that the same building material, the product may differ in size. Differences in the thickness of the walls make it impossible to actually standardize the size of the box for interior doors. The solution of this problem was the release of the door frame with a minimally allowable width that guarantees the strength and a good boards, which will close the remaining thickness of the wall of the opening. What kind of doors are for doors and how they are installed - tell us in our article.

DOOR - what it is

We will try to briefly explain what kind of good. Dobor is called decorative planks of certain sizes and textures for installation in the openings of interroom doors, if the width of the wall exceeds the size of the door frame. In the photo below, it is clearly displayed that it represents this door item:

Most of the produced modern interior doors is made from tree fiber materials, simply speaking, MDF, therefore, the goodholds manufactured to them are also made of it. Door manufacturers from a natural massif practice the production of a good plan, both from the massif and from MDF covered with a natural veneer. Production material does not affect the order of installation of the good.

Dobors on interior doors may differ in design, as well as have standard width dimensions: 100, 150, 200 and 250 mm.

Depending on which constructive features are characteristic of the model, good things are simple or telescopic. A simple design of a simple design is installed close to the box.

Adjustable good is equipped with a groove on one side and a notch on the other, with the help of which is connected to the grooves and recesses in the box on the principle of the Euro harvesting principle. The presence of groove facilitates the adjustment of the protruding part after the measurement and preparation of the plank to the installation, and also allows you to "simmer" the door design faster and easier.

Installation

Door dobors are mounted using foam, finish nails or self-tapping screws, depending on the preferences of the installer, since the stability of the attachment fastening does not depend on the method of installation of the good. Experienced installations recommend installation of non-foams, as this method is the easiest and less time. Adjustable good for interior doors is mounted only with mounting foam.

Installation on mounting cloves

The drill with a diameter of 1 mm in the face of a good bar, which will then lie down to the box, drill holes at a distance of 15-20 cm from each other, the depth of the holes should be 0.3 - 0.5 cm less than the length of the carnation. Finish carnations are inserted into the drilled holes until it stops the sharp end. If non-finishing nails are used, the caps are mandatory.

Parts of the goodness separately are riveted by the episodes of carnations on the door frame. Rubber hammer or ordinary metallic through a wooden laying nails are clogged into the box. Accurate dimensions and accurate actions minimize the possibility of gaps or cracks that can be eliminated by the analysis and re-installing of the good or using the plaster on the tree to the tone. Such corrections worsen an aesthetically nice view of the goodness and testify to the amateur of the installer.

Dobly construction fixed by finish nails strengthen the strips of painting tape, purified from possible dirt, dust and smeared slightly. After that, proceed to fission. Dobors do not differ in weight, so the fiscal foam is suitable for installation. After the foam is completely dried, the protruding parts are cut off and can be started to install the platbands. With step-by-step instructions, how to put a good-to-interior door, you can read the video below.

Finishing cloves reliably press the chalkboard to the door frame, but do not hold it from pulling out, which is a significant disadvantage of this method of installing the good.

Mounting with screws

From the end side of the bar with a drill on a tree, a hidden hole is cut. The diameter of the drill must be at least 1-2 mm less than the thickness of the challenge, and also correspond to the size of the screws of the self-press. The length of the self-samples is selected in such a way that when drilling, they entered the door frame for 2-3 turns. A larger number of revolutions can trigger the crack and chip on the box.

The hole is drilled on the retreat of 1-2 mm from the front side of the dough, it is allowed to drill through the irrigation side of the plank. It is recommended to keep the drill when working under a slight inclination to eliminate the possibility of drilling the front side of the good. A sufficient amount of self-tapping screws for fixing the lateral part of good - 4 pieces, respectively, 4 holes for them are convicted.

Installation of door sneaks begins with incomplete screwing of the screws in the designed holes. Thus prepared, the Dobly Plank is pressed against the door frame and fastens a drill. It is recommended to start installing a bad game on interior doors from vertical slats and finish with a horizontal board. If you have noticed that the self-tapping screw is difficult, do not make undue effort. Recommended for a couple of revolutions to unscrew such a self-tapping screw and then spin again.

After screwing the top plank, it is important to check the design of the good for the presence of a loose fit to the doorway, which is corrected with a dense pressing of the plank to the box with remedies. For example, construction scotch. By the same scotch, the whole of the good is designed to avoid deformation when the drying foam drying is swelling. The vertical good part is enough 3-4 strips of construction tape, for horizontal - 2-3 strips. If it is impossible to glue the tape to the uneven surface of the wall, use wooden spindles for struts.

The minuses of the installation of a kind on the self-tapping screws are the complexity and duration of the process, the high probability of cracks appearance, chips with an unsuccessful drilling or when the tool is incorrect.

Marking of fair slats and installation with foam

The installation of the foam is considered the simplest and faster way, as it will not be necessary to pre-drill something or score into the planks. How to put goodness with foam on the interroom door?

A fitting of a chalkboard in the size of the doorway begins with the upper horizontal part, which first cuts the length, and then in width. The width of the dough is marked with a pencil after the boards to the thickness of the wall of the opening, and then overlook the board with an electric jigsaw. Side vertical strips are adjusted in the same way. An important condition is the accuracy of measurements. Pre-assembly of the problem should not reveal the presence of gaps between the side and top planks.

The accuracy of the size and aesthetically pleasant appearance after the installation depends on the measuring instruments, such as a ruler or construction kit. The second option is more preferable due to greater accuracy and the minimum probability note the uneven line for the cut.

Installing Sobors on interior doors begins after you make sure that all parts fit tightly to each other and to the way. The upper part of the chalkboard is fixed with the help of sweater between the door frame and the wall of the opening. The optimal option is the greasy tape, which is characterized by a high level of tensile strength in a perpendicular direction, easily withstands foam efforts when swelling. It is enough 3-4 strips on the side-voltage planets and 2-3 on the top board. Another good option for fixing the problem is the squeezing by wooden pegs made by their own hands.

Then the vertical slats are installed in such a way that the upper bar lay on them by level without gaps or cracks. The side parts are recorded also with the help of wedges or painting scotch. Then the space between the good and walls of the opening is filled with the mounting foam under low pressure. First, the edges are pointing in the width of the opening, and after dried up the remaining emptiness is filled.

We pay attention to the installation of goodbirds and platforms are performed after drying the foam on the door blocks. Interior doors in front of the final installation stage should simultaneously have a day for grazing the mounting foam.

The telescopic voluntary bar is installed on the same principle of action (fit along the length of the upper and lateral planks), the difference is the technology of gradually increasing the design. It is strongly recommended a preliminary assembly of the entire design and its subsequent installation in the opening, since during the filling of the empty space, the foam increases the likelihood of violation of the compounds and skewers. First, the first voltage rail is mounted around the perimeter, after it is fixed as follows, etc.

Before giving it, it is recommended to clean the surface of the wall and the inner part of the Dust Card from Dust / Dirt if available, and then moisten. Wet clean surface increases the adhesion of the mounting foam and the subsequent reliability of the stubble design.

Advantages of installing voltages for interior doors using mounting foam:

• High strength and reliability of the design;
• The exception is to spoil the material with unsuccessful drilling or drilling nails;
• No cracks and chips on a good and door frame during installation;
• Fewer action during operation;
• Quick installation;
• Smaller installation cost when involving specialists compared to other methods.

We hope that the advice, how to put goodholders will be useful and you can easily install them on your interroom door.

If you put a door frame and it is less than the thickness of the wall, this gap is needed to close something. To do this, use dobors to the interroom door. The fact that they represent themselves, what they look like, how to put them, and we will speak on.

What is a good

When the situation occurs when the box turns out to be less width than the thickness of the wall. In such cases, a special board is used, which is attached to the door frame, closing the remaining space. This board is called a good room for the interroom. The name "Dobly," and "Doblyar Planka" is still found. On it, then you can attach a platband that closes the gap between the good and the wall.

DOOR - Board for expanding the door frame to the thickness of the wall

That is, the door for the door is an extra part of the door frame. It is a board of specific sizes that join the door frame. They put it on the one hand - the opposite of the one in which the door opens. You can still call this board with an expander - displays its real purpose.

If the wall thickness is greater than 140 mm, you have to put the door frame extender - a good chalkboard

There may be nuances on docking a good. Often the door frame is specific - with a special relief (protrusions, depressions, roundings). Then you have to look for a good specifically of this company, otherwise they will dock them problematic.

Materials and sizes

Each of the manufacturers produces a certain set of good boards, in which the length is fixed - 230-250 cm, the thickness / width varies. For example, there are options (thickness, width, length):

Thickness and width - each factory has its own. There may be 60 mm, and 65 mm or 75 mm. In general, anyone. What if none of them is suitable for your case? Take a greater width than required, then freeze unnecessary. And if your opening is wider than all available options? Order the desired size (many manufacturers make to order) or splicing two smaller sizes. Another option is to use telescopic platbands. They are with a bend for an angle that can block your width shortage.

What materials do goodholders on interior doors? Of the same factors:

• wood;

MDF and chipboard can be covered with veneer, elevated. Wooden can be with or without processing. Select the material and color to the door frame. And this is another reason to take the same manufacturer - even if the name of the color / texture coincides, there is no guarantee that they will actually be the same.

Types of kind

Dobly, there are two types:

Dobor on the interroom with straight edges is the most common board. In this case, it must be chosen only in color and size. Dobor pressed to the box, fixed by the defamion by self-drawing. One of the ends of a good plank can be processed. This is necessary if the platband can be shifted.

Not too convenient to fix this type of good. It is necessary to think about not to split the bar, how to close the hats of self-tapping screws. However, you do not have to pick up the form of grooves / protrusions, which is far from easy and binds only to one manufacturer.

Telescopic door good has a pre-shaped groove. From the point of view of the docking - this is a very convenient option: the protrusion was driven into the groove, they were configured to the complete coincidence and the entire installation. But only if the coincidence is perfect. What else is a telescopic good story? You can install a telescopic platband (if it fits).

How to install dothor on the interroom door

At this point, we will talk about ordinary straps - with straight ends. Sell \u200b\u200ba length of 2100-2300 mm. Three planks are needed on one door: one to the right and on the left, and the piece of the third will go to the upper part. If you simultaneously put a few doors and you have the same color, one plank will go to two "tops".

The strips are width and length usually more than it is necessary, so they will have to be trimmed. What tool? The fact that you have. Suitable by a juda, which saw DMF, chipboard or wood. For the design of the corners, it may take a stub (if you are going to poison the box (and good) under 45 °. It is convenient to use it to "not fill up" sleep and make it strictly perpendicular.

Remove the sizes and make blanks

Before installing dobors to the interroom door, you need to find out the exact dimensions of the expansion planks. To do this, install the door frame in the doorway, fix it. On the plan, draw the opening, it will be easier to write dimensions. Next, we take the roulette and the level, measure the size of the sizes that you need.

Now, in size from standard slats, cut out those that we need. Marking marks to make a pencil - a simple pencil is clearly visible on light boards, you can take a white on dark. Carved strips try in the opening, if necessary, cut a little.

Collect

Before putting good to the interroom door, they must be combined with each other. Cut-off Dobly Planks decrease on the floor in the form of the letter "P". If they have a treated edge - lay out so that the edge is on the one hand. The planks will need to be connected to each other. If they are made of MDF or chipboard, you must first sear the holes in the upper crossbar.

To do this, it is better to take the square (ideally - carpenter, but the usual school is suitable). On the bar carry out a line that marks the middle of the thickness of the plank. If the thickness of the chalkboard is 10 mm, the line passes at a distance of 5 mm from the edge. If the plank is in a thickness of 15 mm - at a distance of 7.5 mm. On this line, we put two points, and then drill holes. Diameter - 1 mm less diameter of self-tapping screws.

Next, the holes must be transferred to long planks. To do this, we connect them, equalize the edges. With the help of drills, we carry the mark on the end of the bar, then deepen to the required length (by the length of the self-press). By making holes, we connect the planks, tighten the fasteners. Dobor on the interior door half assembled. But do not rush to attach the second bar. We need to try on the already collected "on the place".

We put the assembled M-shaped part into place, driving the planks in the groove in the door frame. The upper jumper turned out more (we measured it so much). We take a pencil, put a mark where the groove begins. Try to be accurate, as it is important. Surplus can not cut off. Just spend the line and make markers on it, then drill holes. After the assembly, the letter "P" is obtained. Good to the interroom door collected, now it is necessary to install it and secure.

Installation in the door frame

Now the good can be installed. Check the opening. If the doors put on a foam, it can burn the groove. Surplus cut off so that the strips go free. Insert the P-shaped design in the groove, tapping the palm by the end. We begin on top, then on the sides.

We take the greasy tape, they fix the planks to the walls. If in some places, the good for the interior door is loosely adjacent to the box (there is a slot), you remove this gap with linings. To do this, you can use mounting wedges. If there is no, make out of foam. We just need to put the bar exactly, for this purpose the dense foam is enough.

Fastening a challenge box

Also need to align a good to the interroom door to the level. Focus on the eye do not stand, use the level. With the help of the level and wedges, we remove all the protrusions and grooves. In the process, fix the aligned sections with painting scotch. The distance between the patches is 40-50 cm. On one above and below (retreating about 10 cm), and further with equal intervals.

Next, using mounting foam with low expansion, fill it with the space between the wall and the hard plank. Before applying, read the instructions on the cylinder. Perhaps the surface is better to moisten. In any case, it is necessary to lay the mounting foam in stages, otherwise it can exit the level of good. We will have to dypipe, clean and fed new.

So, first we apply a foam of the gap. A bit one strip. In parallel, we make stripes on the whole width near the "tapes" (an example of a foam on a good door in the photo above the right). Foam in the area of \u200b\u200btapes will give a stability plank, a band in the long part - near the junction - wait for the commander to the groove, but it will not disappear.

We leave the foam on the side straps to polymerize, but for now we are filling the gap on top. If it is as big as in the photo, it makes no sense to translate many foam. It is easier to cut the "bookmark" from the foam, put a suitable size of a wooden bar. In size it is slightly less than free space. From all sides there should be a gap of at least 1 cm. But too big clearances are not needed.

• Under the mortgage detail we lay small pieces of foam of 1 cm thick or so.
• We apply a snake layer of foam on the back wall (if it is).
• We put the mortgage bar, fill the slots around the perimeter of foam. Again, it's not too much so that the bar of the foam does not argue down.
• If there is a need, we put the "facial" bar (in the photo above the left below). If the Brawn widths grabs, we skip this stage.
• Align the position of the Dobly Plank with the help of a building level, fix the painted scotch.

After the first layer of foam froze (time is indicated on the cylinder), fill in the rest of the space. If a good width has a significant width on the interroom, it is possible to apply a foam in two stages. But every time you need to wait for the polymerization time. After that, it remains only to install platbands.

How to fix a good to the door box if it is thicker than the selected quarter

Often, good is thicker than the quarter chosen in the box. What to do then? How to make sure that the good restrained without cracks and held tightly? There is a simple way - to drill holes to drill holes, screw the screws, then cover the holes to the tone plug. Everything is more or less clear, but not very beautiful - the plugs are still visible.

There is another way. We need suspensions for drywall. Only they should be the most durable and thick. From the suspensions separating part of the ribbon with perforation. Every two parts are obtained from each. We still need small self-tapping screws (flea). Perforated ribbons are screwed to the door frame around the perimeter - at the angles by retreating 10-15 cm, also below, and at a distance at a distance of 40-50 cm.

Self-tapping screws by retreating 1.5-2 cm from the edge of the box (middle photo). One screw to a piece of metallic ribbon is enough. When the door frame set, the tape will hang around. These planks are thin, so there will be no problems with the most small gap. If a good on the interior door of the same width, just insert it. Plates due to elasticity pressed it tightly.

If a good wider, first bend them to the front part, then return it back. Due to the fact that they are not fixed in the edge, they are curved, become like an arc.

This may happen - without the slightest clearance

Now insert the good planks, the crying between the plates and the groove. They will tightly press the bar. The gaps will not be visible even upon closer.